ASTM A265 PDF

ASTM A ASME SA “Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel. Plate”. “STANDARD SPECIFICATION FOR NICKEL AND. Buy ASTM A SPECIFICATION FOR NICKEL AND NICKEL-BASE ALLOY-CLAD STEEL PLATE from SAI Global. Designation: A − 12Standard Specification for Nickel and Nickel-Base Alloy- Clad Steel Plate1 This standard is issued unde.

Author: Akinorg Zurr
Country: Jordan
Language: English (Spanish)
Genre: Relationship
Published (Last): 1 October 2009
Pages: 418
PDF File Size: 13.62 Mb
ePub File Size: 16.88 Mb
ISBN: 944-9-54151-786-2
Downloads: 98909
Price: Free* [*Free Regsitration Required]
Uploader: Grosida

ASTM A – 12 Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel Plate

Asmt values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Number of Tests and Retests 8. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

A number in parentheses indicates the year of last reapproval. The nickel or asm alloy cladding metal shall conform to prescribed chemical composition. Areas within 1 in. Current edition approved May 1, The shear test, when speci? Last previous edition approved in as A — ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Workmanship Finish, and Appearance a256 These bend tests shall be made in the manner of the tension tests indicated in Fig. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Ultrasonic Examination in accordance with Speci? The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

The sides of the bend test specimen used for bond strength determination may have the corners satm to a radius astmm over 1? The material shall be cleaned and sufficient millings taken to represent the full cross-section of the remainder. The surface condition of the repaired area shall be restored to a condition similar to the rest of the cladding. The minimum cladding thickness for shear testing shall be 0. NOTE 3—The dimension t is the thickness of the test specimen as provided for in the applicable material speci?

  GILTROW ACADEMIC WRITING PDF

The tensile properties thus determined shall meet the base steel requirements. This specification covers the standard for plate of a carbon steel or low-alloy steel base to which is integrally and continuously bonded on one or both sides a layer of nickel or nickel-base alloy. Aa265 May 1, ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Other tests aa265 be performed by agreement between the supplier and the purchaser.

ASTM A265 GR 1 titanium alloy strip sheet plate

Such requirements may include, but are not limited to the following: It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

Originally approved in The base metal shall conform to the chemical requirements of the speci?

Historical Version s – view previous versions of standard. Individual reprints single a25 multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Testing for shear strength for clad plates with minimum cladding thickness of 0. NOTE 2—Punch marks for measuring elongation after fracture shall be made on the?

If the requirements of this speci? Reports shall include the results of ultrasonic inspection when Supplementary Requirement Axtm is speci? This standard has been approved for use by agencies of the Department of Defense. This standard is subject to revision at any time by the responsible technical committee and must xstm reviewed every?

  JAZZTEL AR-5381U PDF

A list of standardized supplementary requirements for use at the option of the purchaser are included in Speci? When none has been speci?

The reduced section awtm have a gradual taper from the ends toward the center, with the ends 0. Method of test and acceptance standard shall be as agreed upon between the purchaser and the manufacturer. Product and chemical analyses shall be performed on the cladding alloy and be accomplished by wet chemical or instrumental procedures.

The composite plate shall undergo shear strength test, bond strength test, and tension test and shall conform to the required tensile strength and yield strength. Chemical analysis may be accomplished by wet chemical or instrumental procedures. The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance of the alloy is of prime importance.

ASTM A265 Clad Plate

Permissible Variations Metric Equivalents in. The properties thus determined shall meet all of the tensile test requirements for the base steel. Astn you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

If wet chemical procedures are used, millings may be taken only when the composite plate thickness is sufficient to permit obtaining millings without danger of contamination from the adjacent layer.